Protezione oscillante con bussola antisfilamento PO-BU
PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing
PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing
PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing
PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing
PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing
PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing
Specifications
The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing is the combination of our PO Oscillating Rigid Protection and our BU Anti-Disengagement Bushing and it is used in oscillating, piston-rod applications requiring that the trapezoidal screw be prevented from disengaging from the Screw Jack in the event of an accidental overstroke. The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing, applicaple on all TP models, is a special PO Oscillating Rigid Protection with a trapezoidal thread which guarantees the full load support during the attempted overstroke. Please be aware that in this particular configuration, the payload is supported by the Rigid Protection tube and the lower eyelet; therefore, due to the risk of deflection, it is advisable to use caution with particularly long strokes. Please keep in mind that the use of the PO Oscillating Rigid Protection and a rod-end, does not eliminate lateral loads. When working with compression loads, it is necessary to verify the load capacity under the 2nd Euler's Law: when using the formualae please consider the center to center distance between the eyelet and the rod-end. A motor can be installed directly on the screw jack. Please keep in mind that even a single overstroke accident (with consequent impact of the BU Anti-Disengagement Bushing with the main body of the unit) can irreparably damage the internal gearing.
The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing is the combination of our PO Oscillating Rigid Protection and our BU Anti-Disengagement Bushing and it is used in oscillating, piston-rod applications requiring that the trapezoidal screw be prevented from disengaging from the Screw Jack in the event of an accidental overstroke. The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing, applicaple on all TP models, is a special PO Oscillating Rigid Protection with a trapezoidal thread which guarantees the full load support during the attempted overstroke. Please be aware that in this particular configuration, the payload is supported by the Rigid Protection tube and the lower eyelet; therefore, due to the risk of deflection, it is advisable to use caution with particularly long strokes. Please keep in mind that the use of the PO Oscillating Rigid Protection and a rod-end, does not eliminate lateral loads. When working with compression loads, it is necessary to verify the load capacity under the 2nd Euler's Law: when using the formualae please consider the center to center distance between the eyelet and the rod-end. A motor can be installed directly on the screw jack. Please keep in mind that even a single overstroke accident (with consequent impact of the BU Anti-Disengagement Bushing with the main body of the unit) can irreparably damage the internal gearing.
The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing is the combination of our PO Oscillating Rigid Protection and our BU Anti-Disengagement Bushing and it is used in oscillating, piston-rod applications requiring that the trapezoidal screw be prevented from disengaging from the Screw Jack in the event of an accidental overstroke. The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing, applicaple on all TP models, is a special PO Oscillating Rigid Protection with a trapezoidal thread which guarantees the full load support during the attempted overstroke. Please be aware that in this particular configuration, the payload is supported by the Rigid Protection tube and the lower eyelet; therefore, due to the risk of deflection, it is advisable to use caution with particularly long strokes. Please keep in mind that the use of the PO Oscillating Rigid Protection and a rod-end, does not eliminate lateral loads. When working with compression loads, it is necessary to verify the load capacity under the 2nd Euler's Law: when using the formualae please consider the center to center distance between the eyelet and the rod-end. A motor can be installed directly on the screw jack. Please keep in mind that even a single overstroke accident (with consequent impact of the BU Anti-Disengagement Bushing with the main body of the unit) can irreparably damage the internal gearing.
The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing is the combination of our PO Oscillating Rigid Protection and our BU Anti-Disengagement Bushing and it is used in oscillating, piston-rod applications requiring that the trapezoidal screw be prevented from disengaging from the Screw Jack in the event of an accidental overstroke. The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing, applicaple on all TP models, is a special PO Oscillating Rigid Protection with a trapezoidal thread which guarantees the full load support during the attempted overstroke. Please be aware that in this particular configuration, the payload is supported by the Rigid Protection tube and the lower eyelet; therefore, due to the risk of deflection, it is advisable to use caution with particularly long strokes. Please keep in mind that the use of the PO Oscillating Rigid Protection and a rod-end, does not eliminate lateral loads. When working with compression loads, it is necessary to verify the load capacity under the 2nd Euler's Law: when using the formualae please consider the center to center distance between the eyelet and the rod-end. A motor can be installed directly on the screw jack. Please keep in mind that even a single overstroke accident (with consequent impact of the BU Anti-Disengagement Bushing with the main body of the unit) can irreparably damage the internal gearing.
The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing is the combination of our PO Oscillating Rigid Protection and our BU Anti-Disengagement Bushing and it is used in oscillating, piston-rod applications requiring that the trapezoidal screw be prevented from disengaging from the Screw Jack in the event of an accidental overstroke. The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing, applicaple on all TP models, is a special PO Oscillating Rigid Protection with a trapezoidal thread which guarantees the full load support during the attempted overstroke. Please be aware that in this particular configuration, the payload is supported by the Rigid Protection tube and the lower eyelet; therefore, due to the risk of deflection, it is advisable to use caution with particularly long strokes. Please keep in mind that the use of the PO Oscillating Rigid Protection and a rod-end, does not eliminate lateral loads. When working with compression loads, it is necessary to verify the load capacity under the 2nd Euler's Law: when using the formualae please consider the center to center distance between the eyelet and the rod-end. A motor can be installed directly on the screw jack. Please keep in mind that even a single overstroke accident (with consequent impact of the BU Anti-Disengagement Bushing with the main body of the unit) can irreparably damage the internal gearing.
The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing is the combination of our PO Oscillating Rigid Protection and our BU Anti-Disengagement Bushing and it is used in oscillating, piston-rod applications requiring that the trapezoidal screw be prevented from disengaging from the Screw Jack in the event of an accidental overstroke. The PO-BU Oscillating Rigid Protection with Anti-Disengagement Bushing, applicaple on all TP models, is a special PO Oscillating Rigid Protection with a trapezoidal thread which guarantees the full load support during the attempted overstroke. Please be aware that in this particular configuration, the payload is supported by the Rigid Protection tube and the lower eyelet; therefore, due to the risk of deflection, it is advisable to use caution with particularly long strokes. Please keep in mind that the use of the PO Oscillating Rigid Protection and a rod-end, does not eliminate lateral loads. When working with compression loads, it is necessary to verify the load capacity under the 2nd Euler's Law: when using the formualae please consider the center to center distance between the eyelet and the rod-end. A motor can be installed directly on the screw jack. Please keep in mind that even a single overstroke accident (with consequent impact of the BU Anti-Disengagement Bushing with the main body of the unit) can irreparably damage the internal gearing.
UNIMEC S.p.A.
Headquarters and Manifacturing Plant
Via del Lavoro, 20
20865 Usmate Velate (MB) | ITALY
P.IVA: 00858110968
INTERNATIONAL INFO
tel: +39.039.6076900
fax: +39.039.6076909
This email address is being protected from spambots. You need JavaScript enabled to view it.
UNIMEC NORTH AMERICA Inc.
USA and CANADA
11 Millpond Drive, Bldg 2
Lafayette, NJ 07848 | USA
telephone: +1 973-362-1427
email: This email address is being protected from spambots. You need JavaScript enabled to view it.