Protezione oscillante con controllo della corsa PO-F
PO-F Oscillating Rigid Protection with Stroke Control
PO-F Oscillating Rigid Protection with Stroke Control
PO-F Oscillating Rigid Protection with Stroke Control
Specifications
The PO-F Oscillating Rigid Protection with Stroke Control is the combination of our PO Oscillating Rigid Protection and our Electronic Stroke Control and it is used in oscillating, piston rod applications requiring a stroke control. The PO-F Oscillating Rigid Protection with Stroke Control, applicable on KT models, is a special PO Oscillating Rigid Protection with two milled areas to allow the installation of proximity switches. Proximity switches are included on demand. It is possible to have more than two milled areas for multiple proximity switches. Please be aware that in this particular configuration, the payload is supported by the Rigid Protection tube and the lower eyelet; therefore, due to the risk of deflection, it is advisable to use caution with particularly long strokes. Please keep in mind that the use of the PO-F and a rod-end, does not eliminate lateral loads. When working with compression loads, it is necessary to verify the load capacity under the 2nd Euler’s Law: when using the formualae please consider the center to center distance between the eyelet and the rod-end. A motor can be installed directly on the Screw Jack. A BU Anti-Disengagement bushing is also required on the ball screw. Multiple BU Anti-Disengagement bushings can also be installed upon request.
The PO-F Oscillating Rigid Protection with Stroke Control is the combination of our PO Oscillating Rigid Protection and our Electronic Stroke Control and it is used in oscillating, piston rod applications requiring a stroke control. The PO-F Oscillating Rigid Protection with Stroke Control, applicable on KT models, is a special PO Oscillating Rigid Protection with two milled areas to allow the installation of proximity switches. Proximity switches are included on demand. It is possible to have more than two milled areas for multiple proximity switches. Please be aware that in this particular configuration, the payload is supported by the Rigid Protection tube and the lower eyelet; therefore, due to the risk of deflection, it is advisable to use caution with particularly long strokes. Please keep in mind that the use of the PO-F and a rod-end, does not eliminate lateral loads. When working with compression loads, it is necessary to verify the load capacity under the 2nd Euler’s Law: when using the formualae please consider the center to center distance between the eyelet and the rod-end. A motor can be installed directly on the Screw Jack. A BU Anti-Disengagement bushing is also required on the ball screw. Multiple BU Anti-Disengagement bushings can also be installed upon request.
The PO-F Oscillating Rigid Protection with Stroke Control is the combination of our PO Oscillating Rigid Protection and our Electronic Stroke Control and it is used in oscillating, piston rod applications requiring a stroke control. The PO-F Oscillating Rigid Protection with Stroke Control, applicable on KT models, is a special PO Oscillating Rigid Protection with two milled areas to allow the installation of proximity switches. Proximity switches are included on demand. It is possible to have more than two milled areas for multiple proximity switches. Please be aware that in this particular configuration, the payload is supported by the Rigid Protection tube and the lower eyelet; therefore, due to the risk of deflection, it is advisable to use caution with particularly long strokes. Please keep in mind that the use of the PO-F and a rod-end, does not eliminate lateral loads. When working with compression loads, it is necessary to verify the load capacity under the 2nd Euler’s Law: when using the formualae please consider the center to center distance between the eyelet and the rod-end. A motor can be installed directly on the Screw Jack. A BU Anti-Disengagement bushing is also required on the ball screw. Multiple BU Anti-Disengagement bushings can also be installed upon request.
UNIMEC S.p.A.
Headquarters and Manifacturing Plant
Via del Lavoro, 20
20865 Usmate Velate (MB) | ITALY
P.IVA: 00858110968
INTERNATIONAL INFO
tel: +39.039.6076900
fax: +39.039.6076909
This email address is being protected from spambots. You need JavaScript enabled to view it.
UNIMEC NORTH AMERICA Inc.
USA and CANADA
11 Millpond Drive, Bldg 2
Lafayette, NJ 07848 | USA
telephone: +1 973-362-1427
email: This email address is being protected from spambots. You need JavaScript enabled to view it.