Montaggio in camera unica e antirotazione a doppia guida CU-PR-A
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System
Specifications
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The CU-PR-A Single Chamber Assembly with Dual-Guide Anti-Rotation System is the combination of our CU Single Chamber Assembly option and our PR-A Rigid Protection with Dual-Guide Anti-Rotation system. The CU Single Chamber Assembly is a completely sealed, oil-bath configuration, indicated for those applications where the service factor requires a constant, continuously operated lubrication of all moving parts. This option is only applicable to the TP Series. It is imperative that the oil fill-up process is completed while the translating trapezoidal screw is fully lowered. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. The CU-PR-A Single Chamber Assembly also requires the installation of the PR-A Rigid Protection with Dual-Guide Anti-Rotation System: this option has a dual function as it serves both as a lubricant reservoir and as dual-guide anti-rotation. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the rigid protection. The Dual-Guide Anti-Rotation System is based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.