Protezione rigida bagno d'olio con antirotazione a doppia guida PR-A-O
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System
Specifications
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.
The PR-A-O Oil-Bath Rigid Protection with Dual-Guide Anti-Rotation System is the combination of our PR-O Oil Bath Rigid Protection and our Dual-Guide Anti-Rotation System. This option, applicable to the TP Series, performs three specific functions: protection of the trapezoidal screw from dust and debris, semi-automatic lubrication and prevention of the inherent tendency to rotation of the screw-jack. During the installation the PR-A-O Oil Bath Rigid Protection must be filled with the recommended lubricant. Every time the translating trapezoidal screw recedes in the PR-A-O Oil Bath Rigid Protection it receives a coat of lubricant. In order to guarantee adequate adherence, it is recommended to use high-viscosity gear oils (1,000 mm2/s) with high-pressure PE Additives. Unimec offers a wide selection of proprietary and recommended lubricants depending on the requirements of the application. A lubrication port is installed directly on the body of the unit while a drain plug is installed on the bottom of the Rigid Protection. For applications with particularly long strokes it is recommended to add the TRO option: an oil-recirculation tube allowing the lubricant to flow from the gearbox to the rigid protection and compensate the pumping effect. The PR-A-O option also includes our Dual-Guide Anti-Rotation System based on two linear guides embedded in the PR Rigid Protection and a no-friction Keniflon-treated bushing connected to the trapezoidal screw. In cases of longer strokes it is necessary to verify that torsional forces may not pose the risk of damaging the bushing. Finally, because the anti-rotation system locks the screw and the end-fitting in a specific position, it is always necessary to specify the exact position of special holes or asymmetrical/non-centered details in the trapezoidal screw.